Yachtbroker for this vessel is Floris Vos 0031 88-2502500<br><br>Concord 47 KoopmansAluminium sailing yacht Koopmans 46, ‘Northern Light’, 14.25 (lwl 11.75 ) * 4.36 * 2.15 meter, built 1998 and launched in may 2000, designed by Dick Koopmans, built at Alumarine BV in Sint Annaland as a Concord 47.5 in Holland under supervision of B. Busman. Teak on deck and coachroof, 9 Goyat deckhatches, aluminium superstructure and aluminium hull in Navy Blue (repainted 2005) with aluminium welded Goyot portholes, round bilged hull, waterdisplacement approx. 20 tons, ballast approx. 5.7 tons lead ballast in the aluminium fin keel topped with aluminium welded top, full skeg rudder, water capacity approx. 450 liters in 2 hull integrated tanks, fuel capacity approx. 800 liters in 2 hull integrated tanks, blackwater hull integrated tank approx. 300 liters and a 15 liter greywatertank for the shower, Whitlock pedestal with an emergency tiller
Classic Burma teak interior with using only one tree, front cabin and aft cabin each with double beds, saloon with comfortable round seat convertible to an 3rd double bed, panoramaview in saloon through 10 mm safety glass, headroom 2.04 meter and 1.93 meter in kitchen area, 1 bathroom with separate shower and toilet, washboil in the aft cabin, central heating on diesel Boost Solo Mini, airconditioning (functioning unknown), HRO 90l/hour watermaker (functioning unknown), waterpressure system, 20 liter hotwaterboyler heated by 220V and intercooler from the genset, Isotherm 160 liter stainless steel refridgerator with 3 drawers, Isotherm 120 liter stainless steel deepfreeze with 2 drawers, 3 burner cooker on 220V AC, Integrated combi oven/magnetron.
Cutter rigged, Keel stepped two spreader white painted aluminium Reckman mast (new 2005), bridgeclearance 22 meter, Harken battcarsystem on mainsail with lazy jacks, Reckman hydraulic electric headsail furling system, Reckman hydraulic electric innerforestay furling system, full batten mainsail 48.8 m2 dacron, furling yankee 56.4 m2 dacron, furling innerjib 22.2 m2 dacron, gennaker 162 m2, Navtec hydraulic backstay adjuster, Navtec hydraulic boomvang, Reckman spipoole stored on the mast, 5 Anderson stainless steel winches selftailing of which 4 electric hydraulic.
Nanni 5250 TDI 85 hp diesel engine, 2.000 running hours, Hurth H630V gearbox with Volvo Penta seal, indirect cooling system, consumption appr. 4.5 liters at 7 knots, stainless steel propeller shaft with rope cutter, 3 bladed Maxprop, electric bilgepump, 24V 600 Ah service batteries, 12V 100 Ah startbatterie for engine and genset, Westerbeke 8 KVA low revolutions genset, shoreconvertor, Mastervolt 24V 70 Ah batterycharger, Mastervolt 1500 Watt invertor, 175 Ah alternator on engine.
Magnetic pedestal compass, Simrad fluxgate compass, Simrad IS-15 depth, Simrad IS-15 speed, Simrad IS-15 wind, Simrad IS-15 repeat, Simrad CA-42 chartplotter inside and Simrad DS-42 outside, Standard Horizon GX2000 VHF with 2nd handset, Simrad radar, Simrad AP autopilot, AIS send and receive.
Edson stainless steel Davits, Simpson Lawrence 24V 1500 Watt electric anchorwinch, Simpson sprint 2000 second electric anchorwinch, 2 stainless steel anchors one with 100 meter 10 mm chain and the other with 60 meter 10 mm chain, bathingplatform with stainless steel swimming ladder, deckshower with cold and hot water.
Hull built in ABS certified aluminium type ALMG 4.5 MnH 321 in the following measurements:
Hull under waterline 7 mm
Hull above waterline 6 mm
Keelplating 8 mm
Deck, superstructure and cockpit 5 mm
Superstructure sides 6 mm
Tanktops and manhole covers 6 mm
Enginemounts 8 mm and 20 mm
Mastfoundation 80 mm and 100 mm
The yacht is built under CE standards but not completed under CE because it is built just before CE was obligated. In the cockpit there is a CE-A plate.
The vessel is registered in the Dutch register. It is also possible to buy this vessel as a business.<br><br>